Supply for 14″ rubber glove with cotton linning-rough finish for Japan

Short Description:

Heavy duty rubber glove, made of 100% natural latex. 14″ length(36cm), rough finish, seamless, cotton lining, left/right hand, 330g/pair, 100pairs/case. Water proof, anti acid and alkali. Using for Isolater, dry box, blast cabinet, glove box, etc.


Product Detail

FAQ

Product Tags

Our eternal pursuits are the attitude of "regard the market, regard the custom, regard the science" and the theory of "quality the basic, trust the first and management the advanced". Supply for 14″ rubber glove with cotton linning-rough finish for Japan, We sincerely welcome overseas customers to consult for the long-term cooperation and the mutual development.We strongly believe that we can do better and better.


Heavy duty rubber glove, made of 100% natural latex.

14″ length(36cm), rough finish, seamless, cotton lining, left/right hand, 330g/pair, 100pairs/case.

Water proof, anti acid and alkali. Using for Isolater, dry box, blast cabinet, glove box, etc.

  • Previous:
  • Next:
  • FAQ Content




  • Be cautious when holding key components that have sensitive contact areas. If you want to be extra cautious you can use tech grade ESD gloves. I recommend ESD Nitrile gloves that have microtextured fingertips that provide excellent grip on all surfaces. 100% nitrile gloves contain no natural rubber or silicone and meet stringent requirements for particles and extractables. In regards to handling try not to directly handle PCB or contact points. For a graphics card try to handle it from the corners or the heatsink. For a motherboard use the corners / sides. If you do not want to use full gloves you can also consider finger ESD cods. If you use your bare hands just have common sense and keep in mind when the contacts are.

    I mistakenly refer to the measurement on the gloves thickness as millimeters, when in fact it is milli-inches. MIL stands for milli-inches and MM stands for millimeters. My bad. Though, that doesn’t change anything I say as inaccurate regarding smaller number = thinner glove.

    ESD Nitrile Gloves:

    http://amzn.to/2rbxvVN

    If you’re trying to prevent fingerprints, wash your hands thoroughly with soap and water, paying particular attention to scrubbing the pads on your fingers. Dry them off well. Then handle the components by the edges, as I demonstrate in all of my computer building videos. If you happen to see a fingerprint, stop. Go wash your hands again! This is a much better plan than using any kind of glove.

    Remember, handle all parts by the edges and there is no place for fingerprints to be left behind! I demonstrate this in every single computer build video I’ve ever done.

    If you’re trying to prevent cuts, these gloves are all too thin to provide any protection from that. Work slower and more carefully to avoid injury. Or put on band-aids prematurely in areas of your hands that you feel you are most prone to be cut.

    Video editing software used to create this video:
    Cyberlink PowerDirector 15 Ultimate:

    https://www.cyberlink.com/products/powerdirector-ultra/

    Screen captures by Camtasia Studio 9:

    https://www.techsmith.com/camtasia.html

    Questions?

    https://www.facebook.com/careyholzmanfanpage

    See more of Carey’s video’s here:

    http://www.CareyHolzman.com



    How I made this sand blasting box from a see through plastic box and a pair of dish washing gloves. A metal sand blasting box is very expensive my home made box is not perfect but it will do the job its supposed to do. Hope you like it I will post part 2 soon please subscribe to my channel its free thank you for watching.
    Visit my free website for more crafty stuff
    www.mycrafttutorials.co.uk

    Send your message to us:

    INQUIRY NOW
    • [cf7ic]

    Related Products

    INQUIRY NOW
    • [cf7ic]