Super Purchasing for 24″ rubber glove with cotton linning-smooth finish Supply to Kuwait

Short Description:

Heavy duty rubber glove, made of 100% natural latex. 24” length(62cm), smooth finish, seamless, cotton lining,left/right hand, 570g/pair. 50pairs/case. Water proof, anti acid and alkali. Using for Isolater, dry box, blast cabinet, glove box, etc.


Product Detail

FAQ

Product Tags

continue to improve, to ensure product quality in line with market and customer standard requirements. Our company has a quality assurance system have been established. Mission: Optimize our professional technology, product and service; Super Purchasing for 24″ rubber glove with cotton linning-smooth finish Supply to Kuwait, Adhering to the business principle of mutual benefits, we have won good reputation among our customers because of our perfect services, quality products and competitive prices. We warmly welcome customers from home and abroad to cooperate with us for common success.


Heavy duty rubber glove, made of 100% natural latex.

24” length(62cm), smooth finish, seamless, cotton lining,left/right hand, 570g/pair. 50pairs/case. Water proof, anti acid and alkali.

Using for Isolater, dry box, blast cabinet, glove box, etc.

  • Previous:
  • Next:
  • FAQ Content




  • Ideally one would want to dawn rubber gloves and wear those throughout the process shown. Although I took the voltage high here at 59 volts at one point I don’t really recommend going that high. I would instead suggest staying under 30 volts. This not only keeps arcing at a minimum but its easier to get uniform color spread with voltages starting at 12 volts upwards to 28 volts for a nice blue color. Dipping in a tank is preferred but otherwise this works for anodizing if you have a power source but are not set up with much. You could in fact get a nice sudued dirty brown or olive drab color with a 12 volt car battery doing this same thing.. It is however always a risk and proper safey measures such as gloves and safety glasses and even a rubber mat by rubbermaid like what I sit on in this video are all good ideas.

    I should have noted in the video also that instead of using a Scotchbrite pad to take any surface oxidation off the metal parts, Smoky Mt. Knife Works sells a little item called, “The RUST Eraser” that every knife nut should have. You can slice these blocks or erasers any thickness you like so these also work to clean up the back spring or other metal areas one has to take surface oxidation off of after you color the liners. These are handy for cleaning out the insides of old folders also. These erasers can fit once you slice one so that it only requires a good swipe once or twice covering the entire area of the back spring width all in one neat sweep. This way you don’t drift into the liners scratching the color off in places as you clean the other parts. If you do anodize this way you will tarnish the metal parts some and if you leave the alligator clip in one place too long it will spark off on you. I don’t recommend doing this if the folder you are going to be coloring liners on has carbon blades and/or backsprings or other parts that can be oxidized to form rust patches. Even stainless can corrode this way so again, it is just for example taking into account that I have done this many times in the past.

    On a lot of the open build type folders being offered today in the industry such as, Benchmade and Emerson liner locks (some Emerson years had one side cheesy cheap stainless liner instead of the titanium but the lock side is titanium) this works great to anodize the liners without even having to take the knife apart. Of course it does nothing to change them inside or on the sides. So if you were to want to color the entire liner inside and out then you’d have to then disassemble the knife. Remember to seal the stainless steel detent ball in the lock and the non lock side on Emerson liners with a dab of nail polish and then remove it after dipping to color anodize. Failing to remember this step could result in a gritty feeling action due to oxidation on your stainless balls from anodizing.. You can also use duct tape if you don’t dip too long and it works just fine in most all cases.



    A cut-resistant, waterproof, windproof winter performance glove.

    Youngstown’s Waterproof Winter Lined with Kevlar combines two signature Youngstown technologies – cut-resistance and waterproof.

    The entire glove is line throughout with Kevlar to ensure cut-resistance and last durability. This glove also features our waterproof technology made up of a warm fleece liner, waterproof membrane and form-fit outer shell.

    Rates a Level 3 on ANSI/ISEA 105-2005 Standard.

    PART #: 08-3085-80
    Sizes: S – XXL

    For more information visit: www.ytgloves.com

    Send your message to us:

    INQUIRY NOW
    • [cf7ic]

    Related Products

    INQUIRY NOW
    • [cf7ic]