Hot new products 24″ rubber glove with cotton linning-rough finish supply for Slovenia

FAQ Content

Living in The Phoenix Metro Area? 5 Key steps to plaster your pool. Visit us: http://arizona.poolsresurfacing.com. Tel. 602-497-0490.

Replastering a swimming pool here in the Grand Canyon state is certainly not a five-minute job. This doesn’t mean that you have to spend money on hiring a professional to do the job. If you are willing to put some time and effort into the project, it is certainly possible to do it yourself. The average swimming pool will require replastering every 7 to 12 years, depending on the method of installation, and how it has been maintained. Don’t want to read this article, then listen to highlights how to plaster an old pool in 5 important steps. https://drive.google.com/file/d/0B_ZToeIOgA2sT0xOckJSanNxTDA/view?usp=sharing

First for the tools and materials needed for the project. You will need the mix for pool plaster, acid wash, paint, soda ash, compressor for air, face mask, cleaning solution, finishing plaster mix, chisel, goggles, sump pump for submerging the pool, mixture for cement or mortar, air hammer, normal hammer, yard brush, sander, putty knife, brush for acid, buckets, hose, rubber gloves, wheel barrow, shovel, paintbrush and sponge. Here are the 5 steps to plaster your old pool.

1. Drain the swimming pool, and use the sump pump to drain all the water remaining at the bottom of the pool. Clean the pool of all dirt and debris. Use the sponge and cleaning solution for this purpose. Make sure you use an environmentally friendly cleaning solution for this purpose.

2. Identify the problematic areas where plaster has peeled off significantly. Pay attention to the edges and corners of the pool. Take away the loose plaster with the chisel and putty knife. Sand the sharp edges where plaster has been taken off. Make sure you sand the areas at least twice to make the areas clean and neat for easy replastering.

3. Spray an acid wash over the surface. Use the acid brush to spread it effectively. It will help give you a new surface that is conducive to applying new plaster. Rinse away the acid wash by using a hose. Now allow the surface enough time to dry. Once it is completely dry, apply a bond coat for replastering with the use of a roller. Let it dry overnight.

4. Prepare the plaster according to the manufacturer’s instructions. Now apply the plaster using a street trowel. Start at the deepest end of the pool. You should make sure that the plaster applied is at least 3/8 inches thick. Make sure the plaster is evenly applied on all areas. Now let the plaster dry completely. Mix the plaster finish, and apply it evenly at a thickness of 1/4 inches. You may use the trowel this time round too. Check for any flaws and correct them before letting the pool dry completely.

5. The final step is to apply the pool paint to cover the entire surface evenly. Using the paint brush in one direction will offer a smooth finish to the job. Do not use the pool until the paint is completely dry.

The aforementioned article highlights how to plaster an old pool in 5 important steps.

https://plus.google.com/114577359797335718075/posts/GWbgTQknjAf

Follow us:

http://arizona.poolsresurfacing.com

http://news.poolsresurfacing.com/feed

http://twitter.com/johnawhitlock

https://www.facebook.com/pages/Pools-Resurfacing/427966440738398#

https://plus.google.com/u/0/b/114577359797335718075/114577359797335718075/videos?_ga=1.232935006.1127244526.1462640408

Description:
　 HY630 is liquid rubber(condensation cure rtv, or tin cure silicone) mainly used for silicone plastic molds, with the advantages of good tensile strength, high tear strength, high temperature resistance, excellent chemical resistance, high duplication times, long-term stability, high durability, etc. This moulding rubber is one of the products with the highest use level in the production of craftwork gifts and its shrinkage is even lower than 2‰. RTV mould rubber and silicone rubber are general called two-component room temperature vulcanization silicone with excellent fluidity and good operational flexibility, easy moulding process, and so on. Add curing agent of 2%-3% at the room temperature, the rtv mould rubber is still operational within 30 minutes,and after 2-5 hours, the silicone elastomer(silicone mold) will be obtained with resistance to deformation, extremely high or low temperature, acid and alkali and expansion. The rtv mould rubber is mainly applicable to mold duplication of poly crafts, resin craftworks, lightings, candles. It is also suitable for fabrication of precision molds.

RTV Mould Rubber Applications:
Plastic molds, silicone soft plastic molds,making molds for plastic toys, plastic crafts, plastic gifts, PU products,stationary products, pavement, and so on. It has a quite broad applications due to its favorable viscosity and hardness.

RTV Mould Rubber Standard Datasheet:
Model
Appearance
Viscosity　 (cs)
Hardness (A°)
Tensile Strength (kgf/c㎡)
Tear Strength (kgf/㎝)
Elongation (%)
Mixing ratio(%)
Operating Time(H)
Curing Time(H)
630
White
30000~38000
30±2
≥3.8
≥2.8
≥380
2~3
0.5~1
2~5

Operation Instruction for rtv mould rubber:
　 The product is a kind of white flowing liquid . If the customer wants to make large products and large size molds, the mold should be made of rtv mould rubber with high hardness. On the contrary, if the mold with fine and precision patterns , it should be made of rtv mould rubber with low hardness. The amount of the curing agent depends on the actual requirements of the customer.

The proportions and reactions of the curing agent and the silicone are listed in the following:
　　1. Curing agent 1% added, the silicone can still be operated within 2.5 hours and can be demoulded after 6-8 hours.
　　2. Curing agent 2% added, the silicone can still be operated within 50 minutes to 1 hour and can be demoulded after 2-3 hours.
　　3. Curing agent 3% added, the silicone can still be operated within 28 – 30 minutes and can be demoulded after 1.5-2 hours.
　　4. Curing agent 4% added, the silicone can still be operated within 10 – 15 minutes and can be demoulded after 1 -1.5 hours.

Any more information abt Silicone rubber, pls feel free to contact Ms. Jojo
Mobile: 0086-15013774669
Fax: 0086-755-89948030
Website: : www.szrl.net
Email:hyxz@szrl.net
Skype: live:siliconerubber
Weichat:8618229852599
WhatsApp:008615013774669