Hot new products 14″ Household rubber glove Iran Factory

FAQ Content

Video tutorial on how to diagnose and repair the blend door actuator on a Ford Ranger. The two main issues with a failing blend door actuator is when you adjust the interior temperature on the hvac control panel, you will either hear a clicking sound or the temperature will be stuck on either hot, cold, or won’t adjust the cabin temperature. If you catch the issue in the right time, then it is repairable and you don’t need to buy a replacement actuator. This particular vehicle I am working with is a 1998 Ford Ranger, but a similar procedure may also apply to Mazda B series models as well.

Website: http://4diyers.com
Patreon: https://www.patreon.com/4diyers
Facebook: https://www.facebook.com/4diyers
Google Plus: https://plus.google.com/+4DIYers
Twitter: https://twitter.com/4DIYers
Instagram: https://www.instagram.com/4diyers/
Tumblr: http://4diyers.tumblr.com
Pintrest: https://www.pinterest.com/4diyers/

Tools/Supplies Needed:
-grease
-cloth
-contact cleaner
-blend door actuator
-gear replacement
-multimeter
-standard/flat screwdriver

Procedure:
-as mentioned above the two main issues is you will either hear a clicking sound in the dash when adjusting the temperature or the temperature can’t be adjusted
-it is located behind the glove box
-remove the contents of the glove box, then bend the sides in and pull down
-this will expose the main duct and the blend door actuator is either a white or black box, this will depend if it’s been replaced before or not and is located on the top
-remove the electrical connector, simply depress the tab and pull out
-the electrical connector can be both back probed using a multimeter when in place or disconnected to test the controller circuit
-wiring may vary between the years so check a wiring diagram specific to your vehicle
-the pinout diagram will say which pin location connects to what part of the circuit
-turn the ignition in the run position
-using a multimeter on the lowest DC voltage setting, check to ensure if there is power at the circuit, along with a sufficient ground
-now setting the multimeter to the lowest ohms setting, we will measure the resistance of the potentiometer in the hvac control panel
-values will vary depending on what your cabin temperature is set at
-if it fails any parts of the test, then there is an issue with the hvac control panel or the wiring
-we can simply remove the actuator and inspect if it’s functioning correctly
-to remove it, simply depress the two tabs on the front and use a standard screwdriver to pop it up
-use the assistance of a standard screwdriver to disconnect the actuator
-another issue is that the shaft can break, either on the unit or on the door within the duct
-if the door has broken within the duct, then the duct will need to be disassembled for replacement
-plug the actuator back into the electrical connector, turn the ignition in the run position and test
-rotate the air temperature control and watch to see if the shaft rotates
-it doesn’t have a large amount of movement and won’t move fast either
-using a smaller standard screwdriver, slowly pop the tabs around the outside
-try to hold it apart so it doesn’t clip closed again
-remove the cap and then everything will be exposed inside
-wipe off any old lubricant
-I used a paint marker just to align the gears to make it easier for reassembly
-then remove the gears and continue to clean off the old lubricant
-inspect gears for any damage
-the small gear driven by the motor, I have seen a replacement on Ebay if yours needs to be replaced and it’s much cheaper than buying a new replacement unit
-clean the potentiometer with electronic contact clean and a clean rag
-do not contaminate this area with any oil or grease and inspect for any damage
-ensure the contacts on the shaft gear which run against the potentiometer is cleaner and make sure they ride correctly on the swipe area
-apply lithium grease to the gears and shafts they ride on
-reassemble the gears, lining everything back up and ensure the case is snapped back together
-test to make sure it is working correctly
-for reinstalling the actuator back onto the duct, if you have moved it, then that’s not an issue
-connect the electrical connector, turn the ignition on and then slowly rotate temperature selector, eventually the actuator will fall into it’s slot, then snap the unit back into place
-test again
-push the glovebox back into place by pulling in the sides again

Thank you to all those who watch my videos and support my content. Don’t forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!

© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

Agricultural film making machine – Model CE55/55-1350
Polystar (Taiwan) – Original manufacturer of Agricultural film making machine

Send your inquiry for Agricultural film making machine to: sales@polystarco.com
Find more info about Agricultural film making machine on: http://www.polystarco.com/en/products_i_F02_LDPE_2_Layer.html

1. Agricultural film making machine for making AB two layer Agriculture film
2. Punching device for punching holes on Agricultural film making machine
3. The high-resistance two layer mulch film produced by Agricultural film making machine is suitable for agriculture or construction application.

Polystar is a professional manufacturer of Agricultural film making machine in Taiwan. We design and manufacture Agricultural film making machine based on every customer’s requirement. Polystar Taiwan produces a wide range of Agricultural film making machine, including Mulch Agricultural film making machine, mono-layer, multi-layer, two layer, three layer Agricultural film making machine, HDPE/LDPE Agricultural film making machine…

Polystar’s efficient, Agricultural film making machine CE is designed for producing high resistant A-B two layer film. The two extruders on Agricultural film making machine are capable of loading two kinds of material. The two layer film produced by Agricultural film making machine is composed of different material and it is suitable for making agriculture film, mulching film, and other agricultural application.

Polystar Taiwan manufactures Agricultural film making machine with higher and lower capacity available from 30-200 kg/hr. Model CE55/55-1350 Agricultural film making machine produces 1200mm maximum films, with capacity of 90-120 kg/hr.

There are three optional devices installed on this Agricultural film making machine — Hole punching device, Bubble controller, Dynisco pressure gauge, and Double winder.
(1) The Agricultural film making machine is installed with hole punching device. The hole punching device on the Agricultural film making machine is able to punch holes on film. The produced film from Agricultural film making machine with punched hole on it is very suitable for agriculture application.
(2) The Bubble controller of Agricultural film making machine is for controlling the film width. If the plastic bubble brakes during processing, it can add air into the bubble automatically.
(3) The Dynisco pressure gauge is also installed on this Agricultural film making machine. This optional device detects the pressure of screen changer on Agricultural film making machine.
(4) The Back to back double winder of Agricultural film making machine is able to wind two film rolls at the same time.

Polystar Taiwan has sold Agricultural film making machine to Egypt, Russia, Ecuador, Chile, Australia, Malaysia, Japan and many other countries around the world for over 25 years.

Send your inquiry for Agricultural film making machine to: sales@polystarco.com
Find more info about Agricultural film making machine on: http://www.polystarco.com/en/products_i_F02_LDPE_2_Layer.html

Agricultural film making machine – Model CE55/55-1350
Polystar (Taiwan) – Original manufacturer of Agricultural film making machine