High definition wholesale 24″ rubber glove with cotton linning-rough finish in Surabaya

Short Description:

Heavy duty rubber glove, made of 100% natural latex. 24″ length(62cm), rough finish, seamless, cotton lining, ambidextrous style (fits either hand), 570g/pair, 50pairs/case. Good resistance against acid and alkali. Using for Isolater, dry box, blast cabinet, etc.


Product Detail

FAQ

Product Tags

We have a highly efficient team to deal with inquiries from customers. Our goal is "100% customer satisfaction by our product quality, price & our team service" and enjoy a good reputation among clients. With many factories, we can provide a wide range of products.
High definition wholesale 24″ rubber glove with cotton linning-rough finish in Surabaya, we have built a reliable reputation among many customers. Quality&customer first are always our constant pursuit. We spare no efforts to make better products. Look forward to long-term cooperation and mutual benefits!


Heavy duty rubber glove, made of 100% natural latex.

24″ length(62cm), rough finish, seamless, cotton lining, ambidextrous style (fits either hand), 570g/pair, 50pairs/case.

Good resistance against acid and alkali. Using for Isolater, dry box, blast cabinet, etc.

  • Previous:
  • Next:
  • FAQ Content




  • TOOL DEFINITIONS: DRILL PRESS: A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted part which you had carefully set in the corner where nothing could get to it.

    WIRE WHEEL: Cleans paint off bolts and then throws them somewhere under the workbench with the speed of light. Also removes fingerprints and hard-earned calluses from fingers in about the time it takes you to say, ”What the…??”

    ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their holes until you die of old age.

    SKILL SAW: A portable cutting tool used to make studs too short.

    PLIERS: Used to round off bolt heads. Sometimes used in the creation of blood-blisters.

    BELT SANDER: An electric sanding tool commonly used to convert minor touch-up jobs into major refinishing jobs.

    HACKSAW: One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes.

    VISE-GRIPS: Generally used after pliers to completely round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand.

    WELDING GLOVES: Heavy duty leather gloves used to prolong the conduction of intense welding heat to the palm of your hand.

    OXYACETYLENE TORCH: Used almost entirely for lighting various flammable objects in your shop on fire. Also handy for igniting the grease inside the wheel hub you want the bearing race out of.

    TABLE SAW: A large stationary power tool commonly used to launch wood projectiles for testing wall integrity.

    HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground after you have installed your new brake shoes, trapping the jack handle firmly under the bumper.

    EIGHT-FOOT LONG YELLOW PINE 2X4: Used for levering an automobile upward off of a trapped hydraulic jack handle.

    E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.

    BAND SAW: A large stationary power saw primarily used by most shops to cut good aluminum sheet into smaller pieces that more easily fit into the trash can after you cut on the inside of the line instead of the outside edge.

    TWO-TON ENGINE HOIST: A tool for testing the maximum tensile strength of everything you forgot to disconnect.

    CRAFTSMAN 1/2 x 24-INCH SCREWDRIVER: A very large pry bar that inexplicably has an accurately machined screwdriver tip on the end opposite the handle. This was a time before pry bars.

    AVIATION METAL SNIPS: See hacksaw.

    PHILLIPS SCREWDRIVER: Normally used to stab the vacuum seals under lids and for opening old-style paper-and-tin oil cans and splashing oil on your shirt; but can also be used, as the name implies, to strip out Phillips screw heads.

    STRAIGHT SCREWDRIVER: A tool for opening paint cans Sometimes used to convert common slotted screws into non-removable screws.

    PRY BAR: A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part.

    HOSE CUTTER: A tool used to make hoses too short.

    HAMMER: Originally employed as a weapon of war, the hammer nowadays is used as a kind of divining rod to locate the most expensive parts adjacent the object we are trying to hit. Also to open the end of a finger or thumb (blowout) thereby causing a lot of blood cleanup on walls, floors, etc.

    MECHANIC’S KNIFE: Used to open and slice through the contents of cardboard cartons delivered to your front d oor; works particularly well on contents such as seats, vinyl records, liquids in plastic bottles, collector magazines, refund checks, and rubber or plastic parts. Especially useful for slicing work clothes, but only while wearing them.

    DAMMIT TOOL: Any handy tool that you grab and throw across the garage while yelling ”DAMMIT” at the top of your lungs. It is also, most often, the next tool that you will need.



    TOOLS
    Dremel
    round stone
    small vise grips or vise
    cold blue an rubber gloves
    Safety glass’s

    Thank you You tuber’s!
    for watching my channel , please give me the thumbs up an like ,please click on the subscribe button , feel free to ask questions . Thank you have an  a nice day!  JD !

    Send your message to us:

    INQUIRY NOW
    • [cf7ic]

    Related Products

    INQUIRY NOW
    • [cf7ic]