Good Quality for Rubber shoe cover-M Munich Manufacturer

FAQ Content

In this video, I show how to fix a common problem with the blower door actuator on a 2010 Ford F-150 XLT. Here is the part that I installed into the truck. http://amzn.to/2f0Vgue

2003- 2008 Blend Door Actuator Ford F-150

http://amzn.to/2oVwtNh

2009- 2014 Blend Door Actuator Ford F-150 (THIS IS THE MODEL I USED)

http://amzn.to/2f0Vgue

2015- Present

http://amzn.to/2qvKL4s

Dashboard Plastic Remover Tool:

http://amzn.to/2pVlmUE

Note: Make sure this fits within your model. I know its hard to find the parts sometimes, so I hope you use these links above as a guide to finding your actuator.

This F-150 would only blow cold air because the actuator for the blower door went out. Before I went this far to replace the part I started a few diagnoses: tested the air conditioner, went under the hood to see if the heater core hoses were hot, and check the internet if this was a common issue. Sure enough, every test lead to a faulty actuator.

The hardest part was jamming my hand through the glove box. In order to get to the 5/16in screw on the bottom, I had to go through the glove box while my left hand was in the dash to help assist. Once I got the screw out it was fairly simple.

Installing the new unit took a little bit of wiggling in there because the actuator and door need to be lined up. It can only fit one way. The gear is keyed for this reason. Once installed, connect the power cord, install the two screws that hold the unit down, and put the dash all back together.

This process took about 45 minutes to complete. After the install I was able to change from hot to cold with ease.

Thanks for watching:
Subscribe- http://goo.gl/nD3r4v
Like
Comment
Enjoy

Description:
　 HY630 is liquid rubber(condensation cure rtv, or tin cure silicone) mainly used for silicone plastic molds, with the advantages of good tensile strength, high tear strength, high temperature resistance, excellent chemical resistance, high duplication times, long-term stability, high durability, etc. This moulding rubber is one of the products with the highest use level in the production of craftwork gifts and its shrinkage is even lower than 2‰. RTV mould rubber and silicone rubber are general called two-component room temperature vulcanization silicone with excellent fluidity and good operational flexibility, easy moulding process, and so on. Add curing agent of 2%-3% at the room temperature, the rtv mould rubber is still operational within 30 minutes,and after 2-5 hours, the silicone elastomer(silicone mold) will be obtained with resistance to deformation, extremely high or low temperature, acid and alkali and expansion. The rtv mould rubber is mainly applicable to mold duplication of poly crafts, resin craftworks, lightings, candles. It is also suitable for fabrication of precision molds.

RTV Mould Rubber Applications:
Plastic molds, silicone soft plastic molds,making molds for plastic toys, plastic crafts, plastic gifts, PU products,stationary products, pavement, and so on. It has a quite broad applications due to its favorable viscosity and hardness.

RTV Mould Rubber Standard Datasheet:
Model
Appearance
Viscosity　 (cs)
Hardness (A°)
Tensile Strength (kgf/c㎡)
Tear Strength (kgf/㎝)
Elongation (%)
Mixing ratio(%)
Operating Time(H)
Curing Time(H)
630
White
30000~38000
30±2
≥3.8
≥2.8
≥380
2~3
0.5~1
2~5

Operation Instruction for rtv mould rubber:
　 The product is a kind of white flowing liquid . If the customer wants to make large products and large size molds, the mold should be made of rtv mould rubber with high hardness. On the contrary, if the mold with fine and precision patterns , it should be made of rtv mould rubber with low hardness. The amount of the curing agent depends on the actual requirements of the customer.

The proportions and reactions of the curing agent and the silicone are listed in the following:
　　1. Curing agent 1% added, the silicone can still be operated within 2.5 hours and can be demoulded after 6-8 hours.
　　2. Curing agent 2% added, the silicone can still be operated within 50 minutes to 1 hour and can be demoulded after 2-3 hours.
　　3. Curing agent 3% added, the silicone can still be operated within 28 – 30 minutes and can be demoulded after 1.5-2 hours.
　　4. Curing agent 4% added, the silicone can still be operated within 10 – 15 minutes and can be demoulded after 1 -1.5 hours.

Any more information abt Silicone rubber, pls feel free to contact Ms. Jojo
Mobile: 0086-15013774669
Fax: 0086-755-89948030
Website: : www.szrl.net
Email:hyxz@szrl.net
Skype: live:siliconerubber
Weichat:8618229852599
WhatsApp:008615013774669