Good Quality 24″ rubber glove with cotton linning-rough finish Stuttgart Manufacturer

FAQ Content

http://tinyurl.com/loqbfz3

Video Highlights
0:18 Kit includes
0:37 First step before starting install
1:20 Cutting to length
3:04 Insulating the Chimney Liner
4:29 How to lower into the chimney
5:40 Next Step will be Attaching to the appliance
6:00 Attaching the appliance adapter
7:16 Installing the insert
7:44 Installing the Top Plate
8:51 Cutting the access liner off
10:23 Attaching the Cap
11:44 Silicone the screws

Robert explains how to install Chimney Liner.

Installing a stainless steel chimney liner is an easy and economical way to repair a deteriorated, unsafe, or inefficient chimney flue. You will be able to install a chimney liner after reading this and watching the video. You can do the job with common household tools. A chimney liner should be installed to reduce the chance of a carbon monoxide leak, chimney fire, and creosote buildup. Chimney liners also improve the energy efficiency of the appliance and makes fireplace maintenance easier.

First, determine the appropriate size chimney liner for your specific setup. The chimney liner diameter size you will need will be the same size of the exhaust outlet on the appliance. The chimney liner length you will need will equal the height of the chimney. we recommend ordering slightly over that amount to give room for error.

Only a few tools are needed for a successful chimney liner installation. You’ll need a tin snips (or a sawzall or hacksaw), drill and bit, flat head screw driver, caulk gun, work gloves, and safety glasses.

Every basic chimney liner kit is going to come with four main components: the stainless steel chimney liner, connector (either a Tee connector or a Stove Top connector), top plate, and rain cap. This video shows a basic stove top installation.The top plate is going to be the main variable for a chimney liner kit.

Start by using your knife and remove the plastic wrap that the liner is coiled in. Once you have the liner out, start to straighten the liner. Make sure to do this on the grass or a soft surface so you don’t puncture it. Straighten the liner out as best as you can. It does not need to be perfect as you will have to do some manipulation to get it down the chimney.

After installing the insulation you will need to get the liner to the top of the chimney. Proceed to lower the liner down the chimney until you reach the damper or smoke shelf. You will need to do some adjustments when you get back inside to get it through this.

Twisting the flexible liner will help you install the liner if you are getting caught or hung up on the chimney walls.

Now you will need to head into the house to finish connecting the appliance.

Once the stove connection has been installed correctly, it is time to connect the stove pipe to the stove. Most stove pipe comes with three screws per connection point. Use your drill and drive the screws into the horizontal part of the tee and through the exhaust collar of the stove. using furnace cement to secure and stop any leaks.

Once the chimney liner is all the way down the flue to the point of the appliance, the next step is to connect the top plate to the top of the chimney. The main function for a top plate is to seal the existing flue from rain, wind and critters from entering the chimney. Start by using your caulk gun and a tube of weather resistant high-temp silicone to run a bead of silicone along the top edge of the clay flue.

Next, thread the chimney liner through the round collar of the top plate so that the top plate is sitting on the top edge of the clay flue.

When you have successfully installed the top plate, the next step is to cut the excess liner flush with the top of the collar of the top plate. Your sawzall or hacksaw will work just fine.

The next step is to secure the rain cap to the top plate. The Cap will just slide over and then tighten the clamp.

Congratulations, you have successfully installed a stainless steel, flexible chimney liner!

Click Here:http://tinyurl.com/lxloa28 To see all of our Chimney Liners.

http://is.gd/tu1AJ4

car cabin air filter

Low air flow restriction
Adhesive forms pocket pleat for the filter
Urethane soft sealing gasket
Mesh support screening
Pleated paper filters

car cabin air filter

Wix Cabin Air Filters are designed to circulate clean air inside the cabin. They filter the contaminants down to microscopic size and provide a linear path for low air restriction. Сar cabin air filter is pleated paper filters and are placed in the outside air intake of the vehicle’s passenger compartment.

car cabin air filter

this is one of the easiest things you can replace in your car. my honda civic at its regular oil change, the dealer informed me @ xxxxx miles you should replace the cabin air filter. when i asked how much, they told me it was going to be around $120. i refused recalling that i saw a very simple DIY on [...] and so my plan to save $100 dollars began.

you take out your glove compartment box, by squeezing the ends of the sides and move the glove box towards you and the car cabin air filter box should be exposed. remove the cabin air filter from the car, take out the air filter and put in your new and clean wix filter you bought at amazon. now you simply put eveything back the way it was and you’re done! simple enough right?

the quality of this filter imo is good, it feels like the OEM filter from honda. so far i have no problems. my last words for this review is to spray the filter with febreeeze or put dryer sheets around the filter (tight squeeze) so whenever you turn on your a/c it smells like a fresh scent. i put dryer sheets in mine so my car smells like fresh laundry when the a/c is on

car cabin air filter

I’m embarrassed to say that I did not even know my Honda Civic had an air filter for the cabin. My BMW and Audi in the past had them, but I just assumed that the inexpensive Honda did not have anything. When I went to buy an engine air filter on Amazon, I thought it was a joke that they were pairing the item with a cabin air filter. Well, no joke, the Honda Civic has a car cabin air filter and it’s hidden away in a little drawer tucked behind the glove box. It was very easy to replace, once I knew that it was in there. You just open your glove box, push in the sides a little bit so the stoppers will let it swing all the way down, and then you will see the black face of the drawer for the filter behind. It just slides right out, swap out the new filter for the dirty one, and slide it back in. The only thing to watch for is to make sure the arrows showing the flow of air are lined up together. The drawer in the Honda had the arrow for airflow pointing downward, so I made sure the arrow on the side of the air filter was also pointing downward when I installed it.

That’s it. Ten minute job at most, even if you take time to explore around behind your glovebox.