China Top 10 32″ Large cuff rubber glove for Naples

Short Description:

Heavy duty rubber glove, made of 100% natural latex. 32″ length(82cm), smooth finish, seamless, no cotton lining, left/right hand, cuff perimeter:75cm, 800g/pair, 50pairs/case.


Product Detail

FAQ

Product Tags

Our company insists all along the quality policy of "product quality is base of enterprise survival; customer satisfaction is the staring point and ending of an enterprise; persistent improvement is eternal pursuit of staff" and the consistent purpose of "reputation first, customer first". China Top 10 32″ Large cuff rubber glove for Naples, With a wide range, good quality, reasonable prices and good service, we will be your best business partner. We welcome new and old customers from all walks of life to contact us for future business relationships and achieving mutual success!


Heavy duty rubber glove, made of 100% natural latex. 32″ length(82cm), smooth finish, seamless, no cotton lining, left/right hand, cuff perimeter:75cm, 800g/pair, 50pairs/case.

  • Previous:
  • Next:
  • FAQ Content




  • This video features EPi’s superior bright dipping process on a brass model train. In the video E-Kleen 163A is used to clean the metal and E-Prep 221 is used to bright dip the metal.

    To learn more about these products go here:

    E-Prep 221: https://www.epi.com/bright-dips/copper-and-brass/#e-prep-221
    E-Kleen 163-A: https://www.epi.com/cleaners/aluminum/#e-kleen-163-a



    TOOL DEFINITIONS: DRILL PRESS: A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, denting the freshly-painted part which you had carefully set in the corner where nothing could get to it.

    WIRE WHEEL: Cleans paint off bolts and then throws them somewhere under the workbench with the speed of light. Also removes fingerprints and hard-earned calluses from fingers in about the time it takes you to say, ”What the…??”

    ELECTRIC HAND DRILL: Normally used for spinning pop rivets in their holes until you die of old age.

    SKILL SAW: A portable cutting tool used to make studs too short.

    PLIERS: Used to round off bolt heads. Sometimes used in the creation of blood-blisters.

    BELT SANDER: An electric sanding tool commonly used to convert minor touch-up jobs into major refinishing jobs.

    HACKSAW: One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes.

    VISE-GRIPS: Generally used after pliers to completely round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand.

    WELDING GLOVES: Heavy duty leather gloves used to prolong the conduction of intense welding heat to the palm of your hand.

    OXYACETYLENE TORCH: Used almost entirely for lighting various flammable objects in your shop on fire. Also handy for igniting the grease inside the wheel hub you want the bearing race out of.

    TABLE SAW: A large stationary power tool commonly used to launch wood projectiles for testing wall integrity.

    HYDRAULIC FLOOR JACK: Used for lowering an automobile to the ground after you have installed your new brake shoes, trapping the jack handle firmly under the bumper.

    EIGHT-FOOT LONG YELLOW PINE 2X4: Used for levering an automobile upward off of a trapped hydraulic jack handle.

    E-Z OUT BOLT AND STUD EXTRACTOR: A tool ten times harder than any known drill bit that snaps neatly off in bolt holes thereby ending any possible future use.

    BAND SAW: A large stationary power saw primarily used by most shops to cut good aluminum sheet into smaller pieces that more easily fit into the trash can after you cut on the inside of the line instead of the outside edge.

    TWO-TON ENGINE HOIST: A tool for testing the maximum tensile strength of everything you forgot to disconnect.

    CRAFTSMAN 1/2 x 24-INCH SCREWDRIVER: A very large pry bar that inexplicably has an accurately machined screwdriver tip on the end opposite the handle. This was a time before pry bars.

    AVIATION METAL SNIPS: See hacksaw.

    PHILLIPS SCREWDRIVER: Normally used to stab the vacuum seals under lids and for opening old-style paper-and-tin oil cans and splashing oil on your shirt; but can also be used, as the name implies, to strip out Phillips screw heads.

    STRAIGHT SCREWDRIVER: A tool for opening paint cans Sometimes used to convert common slotted screws into non-removable screws.

    PRY BAR: A tool used to crumple the metal surrounding that clip or bracket you needed to remove in order to replace a 50 cent part.

    HOSE CUTTER: A tool used to make hoses too short.

    HAMMER: Originally employed as a weapon of war, the hammer nowadays is used as a kind of divining rod to locate the most expensive parts adjacent the object we are trying to hit. Also to open the end of a finger or thumb (blowout) thereby causing a lot of blood cleanup on walls, floors, etc.

    MECHANIC’S KNIFE: Used to open and slice through the contents of cardboard cartons delivered to your front d oor; works particularly well on contents such as seats, vinyl records, liquids in plastic bottles, collector magazines, refund checks, and rubber or plastic parts. Especially useful for slicing work clothes, but only while wearing them.

    DAMMIT TOOL: Any handy tool that you grab and throw across the garage while yelling ”DAMMIT” at the top of your lungs. It is also, most often, the next tool that you will need.

    Send your message to us:

    INQUIRY NOW
    • [cf7ic]

    Related Products

    INQUIRY NOW
    • [cf7ic]