18 Years Factory offer 24″ rubber glove – cotton linning-rough finish to Plymouth Manufacturers

FAQ Content

Watch more How to Get Dreads videos: http://www.howcast.com/videos/510559-How-to-Wrap-Dreads-with-String-Get-Dreads

So today I’m going to show you how to wrap your dread locks with string. I’m actually going to use yarn, mainly because it’s a little more colorful and it’s a little more fun. But one of the reasons why you can use this method to wrap your dreads it’s not only decorative, but it’ll help you combine two dreads together without and it’ll actually look like a design.

So the first thing I’m going to do is I’m going to measure out how much yarn I need. So it’s going to start at the root. I want it just a little bit longer than the actual dread, because once you wrap it, of course, you’re going to take up some of that length. So since this is about right, I’m going to go just a little bit more and cut it. Once that is cut I’m going to grab the actual dread lock that I want to wrap.

I’m going to go in here at the roots and just make enough of a hole to where my finger pokes through and that’s where I’m going to actually start. So I’m going to pull it all the way through and measure them out so that they’re even. Like I said, this is one of the methods you can use to combine two dreads together. So I have the string going through the one dread, the main one I want to combine and then the smaller one.

So I put those two together. I use one of my sides, I hold it so it wont’ move, one of the sides to wrap around. You’re just going to wrap it to make it a little more secure. Wrap it at the base, that’s secure. Then I’m going to take the other side and wrap it the opposite way. Secure it even more. Then I’m going to set that out of the way. I’m just going to clip it, just so that you can get an idea of how I’m going to use the yarn down the length of the dread.

So then I have my two and I’m going to just take it and wrap it around. In this particular sense, because Francesca has such a beautiful curl in her dread, I didn’t want to measure the yarn to the very end, because once you do that it’s definitely going to look different. But his is going to allow it to kind of blend in with the rest of her curls, if we go just half or partial length of her actual dread lock.

So I’m going to hold it there. I’m just going to clip it so it will be out of the way, so you can just follow me. And then I’m going to take the other side and wrap it the opposite way. So I’m going to let land right in the middle of where I wrapped it previously and kind of tighten it up. You can do it as tight or as loose as you want. I’m keeping hers loose because she has a nice curl to it, and as you can see, her dreads are kind of small.

So we would be doing this for her as then a way to make them a little bigger, look a little thicker and fluffier. So I’m not going to wrap it too tight. I’m going to keep a nice, loose tension on it, as you go all the way down. And once I get to where the other side meets, I’m going to tie it in a knot. Tie the two ends in a knot, rather. Another reason I like to use the yarn instead of actual string; you can use string and you can use thread; the yarn is just softer and it’s more bendable with the hair.

If you were running your hands through your hair you wouldn’t really feel the yarn as much as you would string, because it’s just as soft as the hair. And this is 100% wool, so it’s a natural fiber and most dread lock wearers like natural things in their hair. I’m going to cut off the excess, once I get my knot really tight. And you can see if this was the same color of her hair it would just blend right in. But even though it’s not, it’s a little lighter so you actually see it, and if she had maybe four or five more of these, it’ll look very decorative. And that is the way you wrap your dreads with string.

JUAL:
Abrasive Blasting:
Aluminium Cut Wire, Zinc Shot, Sus Shot, Copper Cut Wire, Steel Shot, Steel Grit, Plastick Media, GARNET, Brown Aluminium Oxide, White Aluminium Oxide, GLASS BEADS, PS Ball etc.

Abrasive Blasting Equipment:
Shotblast machine, CLEMCO Blasting machine,KOMPAC Blaster 750 (Blasting Cabinet Machine), Vibratory barel finishing machine etc.

Abrasive Blasting Accecories:
Replacement part Blasting machine

Painting Equipment :
GRACO Airless pump, Paint Pot, Airless Gun, one seal, airless hose, Switch Tip, tip guard and otther spare part airless pump .

ELCOMETER Measuring & Testing Equipment :
Coating Thickness Painting Inspection Instrument, Surface Profile Gauge, Digital Surface Profile Gauge, Testex Tape, Thickness Gauge, Surface Comparator, Keane-Tator Surface Profile Comparator, Rubert and Rugotest Surface Comparator, Ships Propeller Roughness Comparators, Pictorial Surface Standards, Salt Contamination Meter, Chloride Ion Test Kit for Abrasives ConcreteChloride In Test Detection Kit, Dewmeter, Dew Meter, Whirling Hygrometer, Sling Hygrometer, Dewpoint Dew Point Calculator, Magnetic Thermometer, Wet Film Wheel, Hexagonal Wet Film Comb, Wet Film Comb, Destructive Coating Thickness Gauge, Sberg Drill, Dal Thickness GaugeMechanical Coating Thickness Gauge, Coating Thickness Gauge, Surface Preparation, Wet Film Thickness Measurement, Humidity Temperature, Hardness Porosity Detection, Surface Profile Comparator

Contact Info:
Phone:021-3274 8088
E-mail:sandblastingsupply@gmail.com