11 Years Factory Isolater rubber sleeve for Guyana Factories
Short Description:
14”length (35cm), black, smooth finish, seamless, no cotton lining, 350g/pair, cuff perimeter:61cm, double layer thickness:2.2mm. 40 pairs/case. Net weight: 12.8kg/case, gross weight: 13.8kg/case. It can be suitable for sand blasting machine, dry box, isolater operation for arm protection.
Product Detail
FAQ
Product Tags
Our company puts emphasis on the management, the introduction of talented personnel, and the construction of staff building, trying hard to improve the quality and liability consciousness of staff members. Our company successfully attained IS9001 Certification and European CE Certification 11 Years Factory Isolater rubber sleeve for Guyana Factories, We sincerely look forward to hearing from you. Give us a chance to show you our professionalism and passion.
14”length (35cm), black, smooth finish, seamless, no cotton lining, 350g/pair, cuff perimeter:61cm, double layer thickness:2.2mm. 40 pairs/case. Net weight: 12.8kg/case, gross weight: 13.8kg/case. It can be suitable for sand blasting machine, dry box, isolater operation for arm protection.
FAQ Content
Be safe! One viewer mentioned the importance of eye protection, I feel like an idiot for forgetting this. Don’t take any chances, please USE PROTECTIVE EYEWEAR!
Things you’ll need:
-rubber gloves
-eye protection
-well ventilated area
-Radio Shack PCB Etchant Solution ($12-15)
-glass jar and lid
-piece of string or cord (to suspend the knife)
-nail polish
-nail polish remover
-600+ grit sandpaper
-paper towels
-a safe working surface (newspaper, cardboard, etc.)
In this video I demonstrate how to acid etch a knife blade. It’s a simple and easy way for you to add your own creative customization to your knife. This is my first time attempting this project, it was successful, so I am sharing the process. DO THIS AT YOUR OWN RISK. I am leaving a few important tips below, but know that you can screw up your knife. That’s why I did it on a $18 knife this time. Besides that, have fun!
***Important tips***
If you are etching a folding knife…
1. Make SURE to coat (with nail polish) in and all around the pivot hole! If any of that surface is etched, it will affect the action of the knife, and probably ruin it.
2. Make sure to coat the locking surfaces, where the liner or frame lock touches the blade, same goes for a back lock, whatever kind of lock. If you’re unsure, just coat it!
Coat the cutting edge WELL!
Notes about the video: I sped up a lot of it because I didn’t necessarily want to cut out the parts I did the work, yet I didn’t want the video to end up 30 minutes long! If you have any questions at all, ask in the comments, I’ll get back to you. Hope this helps, thanks for watching!
Dispose of your etchant solution safely. Either neutralize it completely, or contact your local waste management office and ask what to do with it. Don’t risk the environmental damage and possible damage to your pipe.
The Process flow:
Waste tyre—ring cutter –strip cutter –dice cutter—crushing— filtering–magnetic screening—rubber powder
Detailed Product Description
waste tyre shreddering and recycling machine is mainly used for crushing waste tires into rubber powder for reuse.
Processing method:
Physic mechanical crushing method at normal temperature of waste tyre:nochemical raw material is required,no waste gas,washte water and soot are discharged, and the cooling water of the equipment is reused,no emission,equipment noise is within the range specified by the country(GB20055-2006),fineness of rubber powder produced by it is adjustable(10 meshes to 30 meshes),take waste tyre as example,the process is as follows:breaking down,crushing,filtering,magnetic separating,grin-ding,then the finished products are produced.
contact: Cathy
mobile: 0086-13939083413
TEL: 0086-371-60317344
FAX:0086-371-60317344
gmail: gashili001@gmail.com
skype: gashili001