10 Years Manufacturer 32”rubber glove-cotton linning Supply to Belgium

Short Description:

Heavy duty rubber glove,  made of 100% natural latex. 32”length(82cm), smooth finish, seamless, cotton lining, left/right hand, 800g/pair, 50 pairs/case. Using for Isolater, dry box, blast cabinet, etc.


Product Detail

FAQ

Product Tags

We depend on sturdy technical force and continually create sophisticated technologies to meet the demand of 10 Years Manufacturer 32”rubber glove-cotton linning Supply to Belgium, Welcome to build the well and long standing business relationships with our company to create a glorious future together .customers' satisfaction is our eternal pursuit


Heavy duty rubber glove,  made of 100% natural latex. 32”length(82cm), smooth finish, seamless, cotton lining, left/right hand, 800g/pair, 50 pairs/case. Using for Isolater, dry box, blast cabinet, etc.

  • Previous:
  • Next:
  • FAQ Content




  • Here I am doing basic glass cutting on a scrap piece of glass, actually it’s a mirror. For much more videos about basic glass cutting, etc. see the playlist: http://www.youtube.com/playlist?list=PL4A57AB2EFB9566F9&feature=plcp

    Do not attempt to cut (pre) Tempered Glass, it cannot be cut and is designed to shatter to small pieces for safty purposes. You can cut (flat) Plate Glass.

    The “glass cutter” does not actually cut through the glass, it just scratches or “scores” it, so it should be called either a “glass scratcher/scorer” or a “tool of glass cutting”.

    The score is then used when you actually break or snap the glass along this “weakened” line (or even curves are possible). Technically, you try to “bend” both sides along the score downward to “open” (not compress) the crack up to the back side of the glass. In the vid. I show holding the piece of glass with my hands as a lot of people seem to do – especially with small pieces, but it’s safer to put the glass on a firm surface first and/or wear gloves.

    To remove the sharp parts after cutting the glass, I used some sandstone I found down by the river. Just about any stone or cement will do, just dont use something too hard like smooth quartz since it tends to just “glide” over the glass. Use both straight and circular motion with the stone at about a 45 degree angle to the glass to bevel it to a non-sharp/thin semi-round surface. It is good though to have an electric grinder or rotary tool like a Dremel incase the break leaves some sizeable bumps of glass areas that would be difficult to grind by hand. If you dont have that, perhaps a larger piece of smooth cement might work ok.

    Be sure to sweep up and vacuum any glass shards.

    Note you can use a flat rule made of metal, wood, or plastic to guide the glass cutter, but be sure its not too thin since you do not want to damage the “cutting wheel” (the part that scores the glass) if it came in contact with metal.

    About the tool I made; the ruler-straightedge with the rubber attached to the back. The rubber (or nylon) was cut from a bicycle inner-tube, and was attached with contact cement which is very sticky and somewhat flexible. This glue is sometimes called “rubber cement”. I got a tube for about $1. I also lightly scratched both surfaces of the rubber for better adhesion of the glue and for better “holding” ability on the glass. I guess you could also use some flat erasor type material too instead of the inner tube material. Silicone rubber or a thin coat or beads of dried caulking might be ok. Some tape can possibly be used to secure the straightrule, but you might have to clean up any residue left from the tape unless you put the tape right on the rule itself. When you cut the bicycle tube, avoid breathing the powder (usually talc or talcum), so rinse the tube segment with hot soapy water and let it dry.

    Keep the “scoring wheel” oiled. I just keep/store that end in a glass with some clear oil in it. I use cheap “mineral oil” from the dollar/drug store.

    Find some flat glass pieces and practice a bit on them so that you are prepared to cut glass when you need to.

    Here is a good website about glass cutters, care and use:

    http://www.freepatternsforstainedglass.com/your-glass-cutter.html



    Contact: Mr Lewis
    Email: lewis@goodeggtraymachine.com
    Website: http://www.goodeggtraymachine.com
    Skype: lewis15863824208
    Mob:+86-15863824208
    QQ: 279684828
    Gtalk: lewis15863824208@gmail.com
    Yahoo Messenger:lewis15863824208@yahoo.com

    We are the professional manufacturer of Pulp moulding Machine and EPE Foam Extruder Line etc in China.

    This machine is a deeply processing equipment of EPE foam sheet/film products, mainly used for the tectorial surface of EPE foam sheet/film. The material can be PE film, plated Aluminum film plastic-coated. Paper plastic-coated fabric and so on.
    The machine can increase intensity, waterproof smooth of foam sheet, and can print character, picture, improving the products, is widely used for the packing of box lining, life vest, wooden floor cushion. Car Havelock, Motor adumbral cushion, electronic appliance, high-top china and so on.

    Applications:
    1) Cushioning and packaging materials for electronic equipment, potteries and
    glassware
    2) Construction-roof insulation, expansion joints, anti-vibration in roofs, walls,tunnels,
    bridges and highways
    3) Insulation of window, air conditioner ducting, industrial chillers, cold storage,
    refrigerated vans, industrial refrigerators and water pipes
    4) Education materials, decorative materials
    5) Sports mats, such as wrestling, judo, gym and exercise mats
    6) Body protective materials, such as helmets, leg and thigh guards, arm, elbow and
    shoulder pads, life saving jackets, and gloves
    EPE foam sheet machine can make different foam sheet width and thickness according to customer requirement.

    Meanwhile, it can also make foam pipe, foam net, foam rod, foam profile and so on through changing mould and machine parts.
    EPE foam sheet machine can make different foam sheet width and thickness according to customer requirement.

    Contact: Mr Lewis
    Email: lewis@goodeggtraymachine.com
    Website: http://www.goodeggtraymachine.com
    Skype: lewis15863824208
    Mob:+86-15863824208
    QQ: 279684828
    Gtalk: lewis15863824208@gmail.com
    Yahoo Messenger:lewis15863824208@yahoo.com

    We are the professional manufacturer of Pulp moulding Machine and EPE Foam Extruder Line etc in China.

    Send your message to us:

    INQUIRY NOW
    • [cf7ic]

    Related Products

    INQUIRY NOW
    • [cf7ic]